文章详情

通过对我们文献的阅读进一步了解我们

汽油焊割机操作方法-深圳火神牌汽油焊割机中英文精简版 2016-07-26

汽油焊割机操作方法(深圳火神牌汽油焊割机中、英文精简版)

(特 别 注 意)

1深圳市环能创机电有限责任公司提示:操作之前一定要先阅读和熟悉使用说明书。

2、装备之前,首先要用高压氧气吹尽氧气管、汽油管内垃圾,以防管内垃圾堵死割炬,造成割炬无法使用。(必须)

3、耐油胶管一头连接油罐汽油出口阀,一头连接割炬,并扭紧螺母,防止空气进入,影响吸附力。

4、使用时首先要扭松油罐加油口阀半圈,一定要外界空气进入油罐内,以免产生负压,造成割炬吸不出汽油而不能正常工作

5、氧气压力根据金属切割厚度而调到正确值。(同乙炔切割相同的氧气压力值)

6、点火时先开割炬综合氧阀,再开汽油开关,看到割咀有汽油雾状喷出,立即点火。扭动割炬综合氧阀及汽油开关,调出火心发蓝发亮、火焰发蓝微黄、没有红色火苗窜出的中性火焰,(火心一定要在割咀外燃烧,以免烧坏割咀)(正常调火时间在3秒以内)。根据切割金属厚度再调节火焰大小,就可以正常切割了。熄火时先关割炬汽油开关,再关综合氧阀。

7、冷枪点火如果调火困难;①可以把点着的割枪割咀在切割工件上来回拖动几下再调火;割咀与工件最好有接近5度的角度,以免死火。②或者把燃烧的火焰火心收回割咀内燃烧3-5秒钟再调火,以上操作可以缩短调火时间,更容易调出满意火焰。

8、停止工作时一定要关好油罐上所有阀门,氧气瓶开关及割炬上氧气、汽油开关,再离开工作现场,以免造成危险。

9、防爆油罐内的金属丝为价格昂贵的高科技专用军工防爆材料,严禁从油罐内掏出来,否则会造成爆炸危险(切记)

10、切割正常标志:切割速度,氧气用量同乙炔--氧相同,点火不滴油,割炬移动中火焰无变化,操作中无死火现象。

 

一、焊炬使用方法(特别注意)

1、准备工作与割炬操作方法相同.

2、油管连接,①如用汽油焊炬;油管一端接油罐出油阀(割阀),一端接焊炬;②如用汽油气焊炬则一端接油罐出气阀(焊阀),一端接焊炬,并且油管内不能有汽油;其它操作两者相同。

3、把氧气压力调至0.2--0.3MPa之间,把油罐上的加油口阀扭紧,焊、割两个阀全部打开。

4、打开焊炬氧气开关,再开焊炬汽油开关,马上点火,交叉调节焊炬上的氧气、汽油开关,就可以调出满意的焊接火焰。(火焰火心一定在焊咀外燃烧,以免烧坏焊咀)关火时先关焊炬汽油开关,再关氧气开关。

5、其它步骤及注意事项与割炬操作方法相同。

二、烤炬使用方法(特别注意)

1、烤炬准备工作与焊炬操作方法基本相同。

2、烤炬使用前把氧气压力调至0.4-0.7MPa。

3、点火时先把烤炬氧气开关开至1-2圈,然后把汽油开关开至1-2圈,马上点火,然后把火焰调出火心发蓝发亮,火焰发蓝微黄的中性火焰,(火焰火心一定在烤咀外燃烧,以免烧坏烤咀)再根据加热工件大小调节火焰大小,就可以对工件进行加热作业了。

4、其它步骤及注意事项与割炬操作方法相同。

割炬、焊炬与烤炬操作方法更多详情,欢迎登录我司网站www.hncjd.com--技术论坛--无压汽油焊割机操作说明书(文章)进行详细了解。

              深圳环能创机电技术部

Torch Operating Guide, Starter Edition

(NOTE)

1、Operate the equipment, you must first read and become familiar with manual.

2, Before connect device, with high-pressure oxygen jet fuel oxygen tube and pipe remain the dust of memory, to prevent dust clogging the torch, the torch does not work.
3, Connect one end of tubing gasoline tank of gasoline export unit, connect the other end of the torch, and pay attention to tightening the nut, to prevent air from entering, the impact force absorption.

4, When used, the fuel tank must be twisted loose semi-circle port device, so that outside air into the tank. In order to avoid negative pressure, causing the torch does not work.

5, Oxygen pressure need to adjust the thickness of the metal cutting to the correct value. (Same with acetylene cutting oxygen pressure)

6, Before ignition, turn on the torch oxygen valve, then open the fuel switch, see the cutting nozzle of the fuel mist spray, ignition immediately. Twist torch oxygen valve and fuel switching, showing that the flame center and high-brightness blue, so blue and yellow flame at the end also did not show a red flame sprang a neutral flame, the flame center to be adjusted to the cutting nozzle, to avoid damage to the cutting nozzle (normal transfer time of the fire in less than three seconds). Finally, according to the thickness of the metal cutting adjust the flame size, you can normally cut through. Always turn off the

torch when the flame gas switch, and then close the oxygen valve.

7,f you feel the flame torch to be more difficult to adjust to the ideal state;1) The point of the cutting torch cutting nozzle on the workpiece in a few drag back and forth, and then adjust the fire. Cutting nozzle and the workpiece is best to have close to 5 degrees of angle, in order to avoid extinction. 2) Another method is to cut back center of the combustion flame nozzle, the combustion of 3-5 seconds, then adjust the flame. These two methods of operation can be adjusted to shorten the time the fire is relatively easy to adjust the flame to the satisfaction of work.

8, When the device after use, turn off all valves on the fuel tank and oxygen bottle switch, and then close the torch switch. Make sure all switches off, then leave the work site to avoid danger.

9, Gasoline tank filled with a metal wire, is patent proof material, do not pull out from the tank, otherwise it will create an explosion hazard.

10, Device is working correctly in the case: gasoline welding and cutting machine cutting speed and oxygen consumption the same with acetylene - oxygen flame cutting, nozzle does not drip at work cutting, cutting torch work when the process of moving the flame no change, no flame suddenly extinguished phenomenon.

 

Welding method

1, Preparation before use, the same welding torch and cutting torch

2, Tubing connections, ① If you are using gasoline torch, tubing one end of the oil tank valve, the other end of the torch; ② If you are using gasoline welding torch, the tank's outlet valve connected at one end, solder the other end torch, and to ensure tubing can not have gasoline.

3, The oxygen pressure adjusted to 0.2 - 0.3Mpa, on the tank filler valve closed, welding, cutting two valves fully open.
4, Open the oxygen torch switch first, then open the fuel switch, once the ignition, cross-regulation of oxygen on the welding torch, gas switch brings up a satisfactory welding flame. Turn off the gas when the torch switch off first, and then shut off the oxygen.
5, Other steps and precautions with the same methods of operation torch.

 

Baking torch manual

1、Preparation before use, the same welding torch and baking torch

2、The oxygen pressure adjusted to 0.4 - 0.7Mpa

3、First switch to open the oxygen torch roasted 1-2 turns, then circle the petrol switch 1-2 turns,  ignition. Then adjust the flame center was bright blue flame, blue flame with yellow neutral flame, (Flame grilled center must adjust to the outside of the combustion nozzle to avoid damage to the nozzle)Then adjusted according to the size of the flame heating the workpiece size, it can work.

4  Other steps and precautions with the same methods of operation torch

 

Cutting torch, welding torch and baking torch for more details torch methods of operation, please log on to our website www.hncjd.com-- Forum - non-pressure gasoline welding and cutting machine operating instructions (article) to learn more.

2016.07.26深圳火神牌汽油焊割机 

 

 

 

在线客服
QQ客服:
点击这里给我发消息
QQ客服:
点击这里给我发消息
旺旺:
点击这里给我发消息

旺旺:
点击这里给我发消息